E.Acc	ERROR! maximum acceleration	24	Maximum acceleration exceeded
E.blc	ERROR! Blockade	26	A blockade was recognized. Pn.85 Bit 4 is at error, no auto-reset.
E. br	Error! Brake control	56	Error: can occur at activated brake control (see chapter 6.9.5) if: the load during the start is below the minimum load level (Pn.43) or the missing of a motor phase was recognized. the load is too high and the hardware current limit is reached.
E.buS	Error! Watchdog	18	Error: Adjusted monitoring time (Watchdog) of thecommunication between operator and PC / operator and inverter has been exceeded.
E.Cdd	Error! calc. drive data	60	Error: During the automatic motor stator resistance measurement.
E.co1	Error! counter overrun 1	54	Counter overflow encoder channel 1
E.co2	Error! counter overrun 2	55	Counter overflow encoder channel 2
E.dOH	Error! drive overheat	9	Error: Overtemperature of motor PTC. Error can only be reset at E.ndOH, if PTC is again low-resistance. Causes: Resistance at terminals T1/T2 >1650 Ohm Motor overloaded Line breakage to the temperature sensor
E.dri	Error! driver relay	51	Error: Driver relay. Relay for driver voltage on power circuit has not picked up even though control release was given.
E.EEP	Error! EEPROM defective	21	After reset the operation is again possible (without storage in the EEPROM)
E. EF	Error! ERROR external fault	31	Is triggered, if a digital input is being programmed as external error input and trips.
E.Flc	ERROR! Flow control	27	The flow control is activated in Pn.91. No input and output for the valve control is selected in Pn.92 and 93.
E.Enc1	Error! Encoder 1	32	Cable breakage at the encoder. Encoder temperature is too high. Speed is too high. Encoder signals are outside the specification. Internal defect.
E.EnC2	ERROR! encoder 2	34
E.EncC	Error! Encoder change	35	Operation of a synchronous motor with intelligent interface: • Encoder not connected at power-on • Encoder was changed This error can be reset by writing on Ec.00 and from version 4.2 via hardware or bus-reset. The fault localization is described in Ec.37.
E.Hyb	Error! Encoder interface	52	Invalid encoder interface identifier.
E.HybC	Error! hybrid changed	59	The encoder interface identifier has changed and must be confirmed via Ec.00 or Ec.10.
E.iEd	Error! input error detect	53	Hardware error at NPN-/PNP change-over or at start/stop measurement.
E.iPH	ERROR! Output phase	5	Phase loss detection at the output
E.InI	Error! MFC not booted	57	MFC not booted

E.OL2	Error! overload 2	19	Occurs if the standstill constant current is exceeded (see technical data and overload characteristics). The error can only be reset if the cooling time has elapsed and E.nOL2 is displayed.
E.OP	Error! overvoltage	1	Voltage in the DC-link circuit too high. Occurs if the DC-link voltage exceeds the permissible value. Causes: poor controller adjustment (overshooting) input voltage too high interference voltages at the input deceleration ramp too short braking resistor defective or too small
E.OS	Error! over speed	58	The speed is outside the defined limits. (can also occur on exceeding of the absolute speed referring to EMF = EMF wrong (servo drives).
E.PFC	Error! PFC	33	Error in the power factor control.
E.PrF	Error! prot. rot. for.	46	The drive has driven onto the right limit switch. Programmed response “Error, restart after reset” (see chapter 6.7 “Response to errors or warning messages”).
E.Prr	Error! prot. rot. rev.	47	The drive has driven onto the left limit switch. Programmed response “Error, restart after reset” (see chapter 6.7 “Response to errors or warning messages”).
E. Pu	Error! power unit	12	Error: General power circuit fault
E.Puci	Error! power circuit unknown	49	Error: During the initialization the power circuit could not be recognized or was identified as invalid.
E.Puch	Error! power unit changed	50	Error: Power circuit identification was changed; the error can be reset by writing on SY.03 at valid power circuit. If the value displayed in SY.03 is written, only the power-circuit dependent parameters are reinitialized. If any other value is written, then the default set is loaded. A power-on-reset is necessary on some systems after writing of SY.03.
E.PUCO	Error! power unit communication	22	Error: Parameter value could not be written to the power circuit. Acknowledgement from LT <> OK
E.PUIN	Error! power circuit coding	14	Error: Software version for power circuit and control card are different. Error cannot be reset (only at F5-G B-housing)
E.SbuS	Error! bus synchron	23	Sychronization over sercos-bus not possible. Programmed response “Error, restart after reset”.
E.SCL	ERROR! speed controller limit	25	Speed controller limit reached
E.SEt	Error! set	39	It has been attempted to select a locked parameter set. Programmed response “Error, restart after reset”.
E.SLF	Error! Software limit switch forward	44	The target position lies outside of the limit defined with the right software limit switch. Programmed response “Error, restart after reset”.
E.SLr	Error! software limit switch reverse	45	The target position lies outside of the limit defined with the left software limit switch. Programmed response “Error, restart after reset”.

Dịch Vụ A.S.C

Danh mục sản phẩm

Dịch vụ sửa Biến tần KEB F4, F5, F6, G6- Đặc trị lỗi E.OC, E.dOH trên KEB F5

Cấu tạo chung của Biến tần KEB

A.S.C VN – Trung tâm bảo hành chính hãng các thiết bị KEB tại Việt Nam

Chúng tôi sửa được những lỗi nào trên Biến tần KEB?

Đặc trị những lỗi cơ bản trên KEB F4, F5 như E.UP, E.OC, E.dOH, E.ndOH, lỗi lệch pha ngõ ra

Chúng tôi có thể Sửa chữa hầu hết các model Biến tần KEB đang có trên thị trường VN

Linh kiện, phụ kiện chính hãng phục vụ sửa chữa

Bo CPU

Chỉnh lưu AC-DC Diod, Nghịch lưu, IGBT

Bo mở SCR, Bo kích IGBT

Bo Encoder

Quy trình 10 bước sửa chữa biến tần tại A.S.C VN

Cam kết chất lượng và Uy tín với khách hàng

Những hình ảnh sửa chữa Biến tần KEB F4, F5, G6, tại A.S.C VN

Dịch vụ Backup chương trình miễn phí cho khách hàng sử dụng dv sửa Biến tần KEB tại A.S.C VN

Dịch vụ Bakup chương trình Biến tần KEB ngay cả khi bị mất nguồn

Video Hướng dẫn cài đặt Biến tần KEB F5

Phần 1: Cài đặt cơ bản biến tần KEB F5

Phần 2: Hướng dẫn cài đặt FULL thông số Biến tần KEB F5

Bảng mã lỗi Biến tần KEB F5 & cách xử lý

Liên hệ với Trung tâm sửa chữa và bảo trì Biến tần KEB chất lượng cao tại HCM

Download tài liệu hướng dẫn

Video hướng dẫn

Hướng dẫn cài đặt Full thông số biến tần KEB F5 Multi part 2

Hướng dẫn cài đặt cơ bản Biến tần KEB F5 Multi Part 1